Go Company

 

 

The article below in relation to How to Install a Bathtub is relatively engaging. Check it out yourself and decide what you think of it.

Installing a tub isn't specifically rocket science, but it does need strong plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult project. If the old tub is easily easily accessible, the task can relocate speedily; if you have to open a wall to remove the old tub as well as position the new tub, the job is a lot harder. In either situation, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the task as well as are comfortable attempting it. Rather than hiring a professional to take over a halfway-completed project, it is better to consider employing one before you begin. Chances are you might require a specialist plumber to make tube links.
This post will certainly assist you set up a new bathtub in your bathroom if you have actually currently acquired a brand-new tub as well as don't need to transform the setup of your previous water system pipelines.
Your tools and also product list ought to comprise the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Shatterproof glass


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, switch on the taps to drain any kind of water staying in the system. The process of removing the existing faucets can be rather problematic due to the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any type of old securing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.

 

 

Suitable New Touches

If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a link to the current supply pipes.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washing machines are in location in between the faucet and the sink. Protect the faucet in position with the manufacturer offered backnut. As soon as the faucet is securely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical faucet connectors. The former kind should be linked to the faucet finishes first, tightening just by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.

 

 

Mounting the Bathtub

Utilizing both wood boards under its feet, place the tub in the required setting. The wood boards are helpful in evenly spreading out the weight of the bath tub over the area of the boards instead of focusing all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the same for the various other faucet.
Activate the water and also examine all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the tub and also check the overflow electrical outlet and also the typical outlet for leaks.
Finally, fix the bath paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has been used at least once as this will certainly resolve it right into its last placement.

 

 

Getting ready for the Setup

First of all, the sustaining framework supplied with the bath should be fitted (if required) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps device to avoid stress on the bathtub.
Fit the flexible faucet ports to the bottom of the two taps making use of 2 nuts as well as olives (sometimes provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be fitted in its last setting.

 

 

Tiling Around the Bath tub

In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, causing the water to permeate the wall surface between the bathroom and the tiling, causing complications with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also are capable of securing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to permit the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently readily available on the market. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof glue and grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

Do you appreciate reading up on Installing A Bathtub? Create a short review further down. We would be delighted to know your opinions about this content. In hopes that you come back again before long. Make sure you set aside a second to distribute this write-up if you appreciated it. Thank you so much for your time spent reading it.

Visit The Following Page

Prices & Booking

 

 

Presented here in the next paragraph you'll find a bunch of great information on the subject of How to Repair and Prevent Bathroom Water Damage?.

Water damage usually occurs in the shower room as a result of the water utilized day-to-day. Sometimes, the damage could be a little mold and mildew from the shower. Other times, it's enormous damages on your flooring. Whatever it is, it is constantly good to understand the reason and also prevent it before it takes place.
This overview will experience some of the typical root causes of water damage in the bathroom. We will likewise examine what you can do to stop these reasons from harming your washroom. Allow's dive in.

 

5 Common Reasons For Water Damage in Shower Rooms

These are the usual factors you would have water damage in your restrooms as well as exactly how you can find them:

 

Burst or Leaking Pipes

There are lots of pipelines lugging water to various parts of your washroom. Some pipes take water to the toilet, the sink, the faucets, the shower, and also several various other areas. They crisscross the tiny location of the bathroom.
From time to time, these pipes could obtain corroded and also ruptured. Various other times, human activity might trigger them to leak. When this occurs, you'll discover water in the edges of your washroom or on the wall surface.
To detect this, keep an eye out for gurgling wall surfaces, mold and mildews, or mold. Call an expert emergency plumber to repair this when it takes place.

 

Splits in your wall surface ceramic tilesv
Restroom wall tiles have been particularly developed for that function. They secure the wall surface from wetness from individuals taking showers. However, they are not indestructible.
Occasionally, your washroom wall surface ceramic tiles fracture and enable some moisture to seep into the wall surface. This could possibly destroy the wall surface if you don't take any activity. If you discover a crack on your wall surface tiles, repair it right away. Don't wait up until it destroys your wall surface.
Overflowing commodes as well as sinks
As human beings, often we make mistakes that might cause some water damage in the shower room. For example, leaving your sink faucet on might cause overruning and also damage to various other parts of the restroom with dampness.
Also, a malfunctioning toilet might create overflowing. For instance, a busted bathroom handle or other parts of the tank. When this happens, it can damage the floor.
As soon as you observe an overflowing sink or toilet, call a plumber to assist manage it instantly.

 

Roof Leakages

Sometimes, the issue of water damage to the washroom might not come from the shower room. As an example, a roof leakage could trigger damages to the bathroom ceiling. You can find the damages done by considering the water stains on the ceiling.
If you find water spots on your ceiling, examine the roof to see if it's damaged. Then, call an expert to aid address the issue.

 

Excess Moisture

It's amazing to have that lengthy shower and splash water while you dance around as well as act like you're doing, yet occasionally these acts could cause water damage to your bathroom.
Splashing water around can trigger water to head to edges and also create mold and mildews. See just how you spread out excess dampness around, and also when you do it, clean it up to prevent damage.

 

Conclusion

Water damage to your bathroom can be bothersome. Nevertheless, you can handle it if you avoid a few of the causes pointed out in this overview. Call a specialist emergency plumber if you see any kind of severe damage.

 

Top 5 Reasons for Water Damage in Your House

 

Anyone who has had a leak before knows the feeling. That mix of panic, confusion and anger whenever unexpected damage pops up in your favorite place, home. The last place you want to bring you stress is your home.

We have combed through our data and have found the top 5 reasons water damage may pop up. Here they will be explained, and we even threw in some tips you can proactively use to prevent water damage in the first place, how you can spot it early, so it doesn’t evolve into permanent damage, as well as some advice on best practices for when water damage does occur.

 

Plumbing issues

 

Water damage is often caused by plumbing issues and it is easy to see, or not see why. Out of sight, out of mind. That’s why it’s important to inspect the plumbing systems in your home at least once a year to ensure that there aren’t any problems with hoses or pipe joints. While inspecting, keep in mind that water pipes do have a certain lifespan. Brass pipes can last for as many as 70 years while copper pipes can last for more than 50 years. The average lifespan for galvanized steel pipes is often between 20 and 50 years, while drain pipes are usually made of either cast iron (which can last for as many as 100 years) or polyvinyl chloride (PVC). Properly maintained PVC pipes can last indefinitely. Factoring in the age of your pipes is important to any inspection or educating your licenced plumber if you decide to bring in professional help.

Have you noticed your water bill increasing? If it is unusually high, that might be an indication of an undetected leak. Buying a water leak sensor that sends alerts to your phone is one way to safeguard your home. You can also check around your toilets, tubs, showers and sinks for any soft spots or moisture. Keep an eye out for loose tiles as well. If you have a dishwasher or a refrigerator with a water line, look for warped or discolored floorboards.

 

Anyone who has had a leak before knows the feeling. That mix of panic, confusion and anger whenever unexpected damage pops up in your favorite place, home. The last place you want to bring you stress is your home.

We have combed through our data and have found the top 5 reasons water damage may pop up. Here they will be explained, and we even threw in some tips you can proactively use to prevent water damage in the first place, how you can spot it early, so it doesn’t evolve into permanent damage, as well as some advice on best practices for when water damage does occur.

At Hippo, water damage was the top claims filed last year. But the good news is that in more than 90% of cases, water damage is preventable.CLICK TO TWEET

Looking out for plumbing problems, leaks and other issues is key to preventing water from destroying your home.

Plumbing issues

Water damage is often caused by plumbing issues and it is easy to see, or not see why. Out of sight, out of mind. That’s why it’s important to inspect the plumbing systems in your home at least once a year to ensure that there aren’t any problems with hoses or pipe joints. While inspecting, keep in mind that water pipes do have a certain lifespan. Brass pipes can last for as many as 70 years while copper pipes can last for more than 50 years. The average lifespan for galvanized steel pipes is often between 20 and 50 years, while drain pipes are usually made of either cast iron (which can last for as many as 100 years) or polyvinyl chloride (PVC). Properly maintained PVC pipes can last indefinitely. Factoring in the age of your pipes is important to any inspection or educating your licenced plumber if you decide to bring in professional help.

Have you noticed your water bill increasing? If it is unusually high, that might be an indication of an undetected leak. Buying a water leak sensor that sends alerts to your phone is one way to safeguard your home. You can also check around your toilets, tubs, showers and sinks for any soft spots or moisture. Keep an eye out for loose tiles as well. If you have a dishwasher or a refrigerator with a water line, look for warped or discolored floorboards.

Washing machine leaks

 

Unless you’re doing laundry (or trying out some of these laundry games), you probably don’t think twice about your washing machine. But if it breaks down, the results could be quite annoying. For example, if the supply hose is damaged or has a faulty connection to the wall or washing machine, more than 600 gallons of water could potentially spill out within an hour. Most people notice this before this amount of water is released, but we have all thrown in a load of laundry and started a project somewhere else in the home. Any amount of water could lead to significant damage, especially if your washing machine is located on the second floor of your home.

 

Bursting water pipes

 

During severely cold winters, pipes can freeze over and burst. That’s more likely to happen if you have certain types of pipes, such as swimming pool supply lines, water sprinkler lines and pipes with minimal insulation that run against exterior walls.

If temperatures tend to freeze in your area, be sure to protect your pipes. Insulate both hot and cold water pipes using heat tape or pipe sleeves available in your home improvement store. If you have water supply lines in your garage, keep the garage door closed as often as possible. Open kitchen and bathroom cabinet doors to allow warmer air to circulate. If you plan to spend some time away from your home, leave the heat on and set your thermostat to at least 55 degrees. You can’t control the weather, but you can put up a good fight to save your pipes.

 

Aging water heaters

 

We have all seen the scene in the movie where the family's basement is flooded by 2 ft or more and the father is yelling and cursing the water heater. Water heaters have a shelf life. Inspect your records to know exactly when it was installed and make a note physically on the water heater itself as well as in your phone to have it replaced every 10 years. It is also worth noting that if you are looking to upgrade, a tankless water heater can last as many as 20 years.

https://www.hippo.com/blog/top-5-reasons-water-damage-house/

 

Do you like more info about How to Repair and Prevent Bathroom Water Damage?? Place a review down the page. We would be glad to see your opinions about this write up. We are looking forward to see you back again soon. Sharing is nice. One never knows, you could be doing someone a favor. Thank you for going through it.

Affordable? Call now!